BRAND NEW MIDWEST PRODUCTS INSPIRED P-40 WARHAWK 48" WINGSPAN CONTROL LINE SHORT KIT #244 DESIGNED FOR THE FOX .35 ENGINE(.29-.40)
I redrew the ribs and wing tips and all the other unique parts in CAD and will laser cut your parts as ordered.
It has been a long time since the 48" Wing Span profile kit was offered for the P-40 in its original format using solid leading and trailing edge material.
My goal is to offer replicas by providing the special and unique parts where builders can obtain the more common parts locally keeping the overall cost of the models down.
NOTE: Short Kit means not a complete kit. You source the standard stuff like balsa sheet, L.E., T.E., all hardware, covering, etc..
Full Size Plans can be found and downloaded from the internet, however I will provide printed (or digital) full size plans as an option.
This Short Kit Contains ONLY the following Cut parts and is perfect for those who have standard material on hand:UNIQUE
CUT PARTS:
- 1/2-INCH-THICK
CNC ROUTED FUSELAGE
-
EIGHT
3/32” CENTER RIBS
-
TEN
1/16” MAIN RIBS
-
1/16”
HALF RIBS (FOR GEAR BLOCKS)
-
1/16”
MAIN SPAR
-
1/16”
SPAR SUPPORT
-
1/8”
WING TIPS
-
1/16”
WING TIP RIBLETS
-
3/16”
FLAPS
-
3/16”
RUDDER AND DORSAL PARTS
-
3/16”
STABILIZER AND ELEVATORS
-
1/8”
PLYWOOD FUSELAGE DOUBLERS
-
1/8”
BELL CRANK PLATFORM
- 1/16” CANOPY DETAIL
Nothing else is included in the SHORT KIT. If you are unsure what a short kit is, please ask before ordering. These kits are considered custom made to order so typically no refunds are accepted.
If you do not wish to have to source all the 'standard' wood to build the kit, I will supply the following additional items at my cost saving you even more time and money.
This DELUXE Short Kit contains everything in the Short Kit above plus the following items:
INCLUDED STANDARD MATERIALS:
- 1/4" SQ. MAIN SPAR CENTER SUPPORT
- 1/8” X 1/4” MAIN SPAR CAP
- 1/16” X 6” CENTER WING SHEETING (TOP AND BOTTOM)
- 1/4” SQ. LEADING EDGE
- 1/8” X 1/2" L.E. HORIZONTAL SPAR
- 1/8” X 3/4" T.E. HORIZONTAL SPAR
- 1/16” X 3” FOR BOTH L.E. & T.E. SHEETING (TOP AND BOTTOM)
- 3/4" X 3/8” GROOVED LANDING GEAR BLOCK
- 3/8” X 1/2" HARD MAPLE MOTOR MOUNT
- SCRAP 1/2" BALSA TO FORM TOP/BOTTOM WING TIP BLOCKS
Whichever option you choose, you will still need the following to complete the flying model.
- 1/32” LEAD OUT WIRE (2 X 36”)
- 3/32” PUSH ROD WIRE
- 1/8” LANDING GEAR WIRE
- 2-1/2” FRONT WHEELS (X2)
- CONTROL HORNS FOR ELEVATOR AND FLAPS
- CLOTH HINGES (OR SUITABLE HINGES)
- 3/4" TO 1” TAIL WHEEL
- 3” CONTROL LINE BELL CRANK
- ENGINE OF CHOICE AND FUEL TANK
AND ALL THE OTHER STUFF NORMALLY USED TO FINISH CONTROL LINE MODEL AIRPLANES
See images for possible additional items needed to complete kit.
Any completed model and/or plane in images are for illustrative purposes only and are not included in this listing. Please DO NOT expect more than what is listed under "what's included". Any questions, be sure to ask before purchasing.
I usually get the kits on their way in about a week depending on materials in stock. Contact me if you need it FAST before ordering so all expectations are met.
Thank you for looking.
Keep those lines tight!
VintagePlaneKits
